If you’re having trouble with a pin or screw on your pocket knife, you may want to know how to remove it. You can either take the knife apart and try to remove the screws on your own, or you can use an extractor.
Coaxing the screw out
There’s more to coaxing the screw out of your pocket knife pins than just pulling it out with your fingers. A little elbow grease and the right tools can go a long way. If you’re working with corroded screws, be extra careful.
For example, a hammer tapped screwdriver can work wonders, albeit in a small scale. You can also get a lot of mileage out of a soldering iron. It can be particularly useful when removing a stripped screw. However, keep in mind that you should be extremely careful when using a soldering iron on a screw that hasn’t been stripped.
The most obvious way to do this is to use a reverse threaded bit to drill into the damaged screw. This is a much more practical solution to the problem, as you don’t have to worry about causing damage to the head of the screw. On the other hand, you can’t be sure how the bit you’re drilling into will behave.
Using a screw extractor
When you have a pocket knife that has pins stuck in it, you may be able to use a screw extractor to remove the pins. Although this is a great solution for an immediate repair, you should be careful when working with corroded or stripped screws.
Screw extractors can be found in a variety of sizes. They are generally designed to be used with a drill. If you need to remove a screw with your drill, you will need to buy a drill bit that is about 1/8″ smaller in diameter than the screws you are trying to remove.
A screw extractor is a tool that is primarily used to remove stripped screws. It uses a reverse threading drill bit that bites into the head of the stripped fastener. This allows the extractor to twist the screw out of its holding device.
The most common type of screw extractor uses a reverse threading drill bit that is about 1/8″ larger in diameter than the screws being removed. Some types of screw extractors also have a burnishing end. The burnishing end helps to clean up the area where the original driver profile was exposed.
Taking apart the knife
One of the most important rituals in a pocket knife is the cleaning. If left unclean, a pocket knife can become rusty and dangerous. The blade can also start to break in and develop a dull edge.
The best way to keep your knife clean is to wipe it down after each use. This can be done with a thin paintbrush or a toothpick. It is a good idea to clean the inside of the handle as well.
It is also recommended to use a food-safe lubricant. Common lubricants include mineral oil and vegetable oil. You can find these oils at local pharmacies.
Make sure to thoroughly dry your pocket knife after each cleaning. This is because wet lubricants can attract grit, hair, and pocket-lint. They can make it difficult for your knife to function.
Use a soft cloth to wipe down the blade. You may also want to use a high-pressure can of compressed air to get the hard-to-remove dirt.
Oiling the blade
Keeping your pocket knife in good condition is crucial. It can extend its life and allow you to perform a variety of tasks. The first step is cleaning the blade. Afterwards, you can lubricate the pivots for more durability. Using a food-safe lubricant is important for preventing rust and corrosion.
For kitchen knives, mineral oil is best. However, you can also use vegetable oils. But remember that vegetable oils can go rancid. So be sure to keep your knives away from the trash.
If you’re using a carbon steel knife, it’s a good idea to store it in a dry place. You should also lubricate the blade at the tang. This is especially helpful if you’re using the knife for cutting fruits.
For folding knives, wet petroleum-rich oil is a common choice. This lubricant has a thin viscosity and is similar to the kind used on sewing machines.
KPL Knife Oil has excellent lubricating performance. In fact, the company says it’s the best lubricant for modern pocket knives. They also provide an applicator needle for ease of application. Their lubricant is formulated to ensure smoothness and prevent premature wear.